+86 15628781468
sellelevator@163.com
The hydraulic loading elevator must carry out the load-bearing operation in strict accordance with the regulations. Otherwise， people and objects may be injured!
8Now the floors are very high. It is very difficult to climb up from the first floor， let alone carry things. For this reason， people invented the elevator， which can easily reach the floor they want to go. However， if it rains，Lifting hydraulic platform it will be very troublesome and affect the normal operation of the elevator. So what should be done correctly after the water enters the elevator?
gParks The models are relatively complete，not badAutomatic hydraulic lifting platformCombine multiple forces to govern together and the prices are also relatively favorable.
The lifting platform has been inspected and debugged before leaving the factory， and all technical indicators meet the design requirements. Only the power supply needs to be connected when using， and the hydraulic and electrical systems basically do not need to be adjusted.
JLittle goatPay attention to check whether the wire rope of each part has broken wires and loose strands. If it exceeds the relevant regulations， it must be renewed immediately. The care and maintenance of wire rope shall be in strict accordance with the regulations.
EyThe size of oil cylinder shall be reduced as much as possible under the condition that the design requirements are met. The smaller the cylinder size is， the faster the lifting speed is.
Brand awareness. Although there are many brands of mobile lifting platform， not all brands have very high knowledge in the market. When choosing， because the reason why this type of product has higher popularity in the market shows that it has strong advantages in all aspects.
The next thing to compare is the quotation of brand products. When comparing the cost performance of the electric lifting platform， the market quotation is also a key aspect. Fortunately， so the quotations formulated can also be accepted by people.
b Some construction site elevators are rented by rental companies and always want to make full use of them，Lifting hydraulic platform but the temporary load rate of the motor (or %) is completely ignored.
AThe damaged part of the elevator that needs to be bandaged and replaced in time is a kind of hydraulic elevator， also known as guide rail hydraulic elevator， which is applicable to the transportation of goods higher than buildings， restaurants and hotel floors. Here is Lipson Machinery to introduce the daily maintenance of the elevator.
EQuality riskWith the increase of demand for boarding bridges mobile boarding bridge sellers increasingly prefer to use the boarding bridge to provide customers with the appearance of hydraulic boarding bridges， and the demand for boarding bridges is also increasing. However， there are not many manufacturers of the corresponding boarding bridges. Many of the companies selling the boarding bridges are leather bag companies. They do not produce them by themselves， and the price is on the high side. The important thing is that they do not know much about the technology of the car exhibition stand， customers who purchase the boarding bridges can directly find professional manufacturers. When selecting and purchasing the boarding bridge， first of all， the factors such as the products scope of use，Lifting hydraulic platform frequency of work， utilization rate rated lifting capacity and so on should be comprehensively considered，not badAutomatic hydraulic lifting platformCombine multiple forces to govern together and the boarding bridge suitable for the units use requirements should be selected. Conduct market research according to the proposed technical parameters. The first condition for selecting a supplier is to see the reputation of the manufacturer of the boarding axle， and then the after-sales service ability. As long as the fixed boarding bridge with good product quality， excellent performance and complete equipment can be selected at a reasonable price.
rMThe first thing to compare is the quality of brand products. In fact， many times it can become a brand product in the market， which shows that it still has certain advantages in quality. However， if we want to have a high cost performance ratio， we will have higher requirements for quality. However， which causes the lifting platform to be unable to work normally，Hydraulic platform_ Hydraulic platform elevator_ Lifting hydraulic platform_ Vehicle-mounted aerial work platform - hydraulic lifting platform manufacturer the platform has been seriously damaged， and the table has tilted. Please carefully check that the general shear-type aerial work platform was put into the market without strict tilt detection before leaving the factory， resulting in many accidents. For tilt detection， the majority of small enterprises do not pay much attention to the detection of this link， This is why there are so many lifting equipment with this problem. The problem of oil cylinder and power unit system is often insufficient power， andIt is also a very important issue to pay attention to.
Good stability: overflow valve can prevent the system pressure from being too high when moving upward. Emergency manual valve: in case of power failure， the car can be lowered to the nearest floor to open the door. Manual pump: in case of system failure， the oil temperature protection device will signal to suspend the use of the elevator and the elevator can be started only after the oil temperature drops.
installyNow we have more and more demands for cargo elevators. Now lets introduce the maintenance of guide rail cargo elevators. When we normally use the rail-type cargo elevator， we should often carry out inspection， maintenance and maintenance， which can not only extend the service life of the rail-type cargo elevator， but also make it more powerful when it works! For example， the transmission part should have enough lubricating oil， the vulnerable parts must be inspected， repaired or replaced frequently， and the mechanical bolts， especially the parts that often vibrate， such as the slewing bearing and lifting arm connecting bolts， should be checked for looseness. If there is looseness， it must be tightened or replaced. Here are the eight steps of maintenance: the important maintenance work of the guide rail elevator. Regularly check the tire pressure of the guide rail elevator and whether the bearing condition is normal; Regularly check whether the structure of the support and panel is in good condition， and fill the bearing and sliding parts with lubricating oil and grease once a month; Vulnerable parts must be frequently inspected， repaired or replaced. Parts that are frequently vibrated， such as bolts and slewing rings， should be checked for looseness. If they are loose， they must be tightened or replaced.
O When the system oil duct is exposed， avoid dust.
The product has solid structure， large bearing capacity， stable lifting easy installation and maintenance， and is an economic and practical ideal cargo conveying equipment for replacing elevators between low floors. The editor will tell you about the daily maintenance of the elevator: when the personnel enter the elevator to work， they must hang the elevator to prevent the elevator from suddenly falling and causing casualties.
pParksThe size of oil cylinder shall be reduced as much as possible under the condition that the design requirements are met. The smaller the cylinder size is， the faster the lifting speed is.
aIThe boarding bridge can be divided into two types: mobile boarding bridge and fixed boarding bridge. The application scope of fixed boarding bridge and the use of mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site， as a remedial measure， the mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a mobile steel structure slope， and the forklift can also drive directly into the truck compartment for batch loading and unloading operations. Only one person can operate without power supply to realize fast loading and unloading of goods.
Introduction to fixed boarding bridge Loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the starting point and end point of the enterprise logistics chain， and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed， but the height of the carriage to and from the ground does not always form a certain height difference or gap between the transport vehicle and the loading and unloading platform. As a result， the forklift can not enter and exit the transport vehicle to directly load and unload goods. Use boarding bridge to provide reliable connectionReliable connection. It enables the forklift truck to enter and exit the transport vehicle quickly for loading and unloading.